Configure your shade sail online
Design, shape, fabric. Ready in 5 days.
Learn more
FIXED SHADE SAILS
ROLL-UP SHADE SAILS
OUTLET & ACCESSORIES
SAILS BY SHAPE
BUYING GUIDE
INSTALLATION GUIDE
APPLICATIONS
BUYING GUIDE
BUYING GUIDE
BUYING GUIDE
Shade sails
Installation guide · Indoor roller shades
Reading time: 9 minutes
This guide covers the Kyma and Recta models, in both manual and motorized versions. Installation is the same: mark, drill, fix the brackets and hang the roller tube. Only the operating system changes, chain or motor. Where the instructions differ between the two versions, the step tells you. You'll need a drill, a pencil and, ideally, a second person.

PREPARATION
The box contains all the components for installation. Remove the protective material and packaging and check that you have:
STEP 1
The bracket height is the one you gave in your order: stick to it, because the shade is made to those measurements.
For marking, use the spirit level profile in the box. It's cut to the technical length needed to position the two plates at the right distance: once you've finished marking, you can set it aside.
The spirit level profile and marking, figure by figure





SO, WHAT DO YOU NEED TO DO?
Mark the profile and the slots of both plates in pencil, at the height given in your order.
⚠ WARNING
Don't mark without checking the level.
If the profile is tilted, the shade will hang crooked and the fabric won't roll up evenly.
STEP 2

You need the drill and a 1/4" (6 mm) masonry bit: drill without hammer mode.
SO, WHAT DO YOU NEED TO DO?
Drill, insert the anchors and fix the plates on the pencil lines.
⚠ WARNING
Don't fix the plates off the lines.
Even a small shift means the brackets won't line up and the roller tube won't seat correctly.
STEP 3
Using the screws provided, fix the brackets to the plates, on the right and on the left.
The plate connects to the bracket on two different sides, and the side you choose determines the type of mounting:
Bracket and plate, wall mount

Bracket and plate, ceiling mount

With both brackets mounted, you're ready for the roller tube.
The two brackets mounted

SO, WHAT DO YOU NEED TO DO?
Choose the side of the plate based on the mounting type and screw on the two brackets.
⚠ WARNING
Don't mix up the short side and the long side.
With the wrong side, the bracket is oriented for the other mounting type and you'll have to unscrew it and fix it again.
STEP 4
The operating system, chain clutch or motor, is already installed inside the roller tube. If you want the chain or the motor on the other side, slide the clutch (or the motor) out of one end of the tube and the idler end out of the other, then refit them the other way round.
Then take the adapter, the part that connects the operating system to the bracket. Insert the longer end into the clutch or the motor. The shorter end goes into the bracket in step 5.
Switching sides and adapter, manual and motorized




MOTORIZED SHADES ONLY
MOTORIZED SHADES ONLY
Before hanging the roller tube, press the button on the motor head to power it on. You use the same button to turn it off when you clean or service the shade.

SO, WHAT DO YOU NEED TO DO?
Prepare the roller tube before bringing it to the brackets.
⚠ WARNING
Don't insert the adapter the wrong way round.
If you put the short end in the clutch or motor, the long end won't fit into the bracket slot and the roller tube won't hang.
STEP 5
Bring the roller tube up to the brackets on the operating side and insert the adapter into the bracket slot.
The opposite side, the idler end, has a spring pin. Bring the end cap up to the bracket and press the pin: it retracts, and when you release it in front of the bracket recess, it locks into place there.
Hanging the roller tube




MOTORIZED SHADES ONLY
MOTORIZED SHADES ONLY
The bracket has a recess for the motor's receiver antenna: thread the antenna through it so it stays hidden.
Don't cut the antenna
Keep it away from metal objects and make sure it doesn't touch any moving parts.

SO, WHAT DO YOU NEED TO DO?
Operating side first, then the idler end.
⚠ WARNING
Don't push the roller tube in without pressing the pin.
The pin stays outside the recess and the tube isn't locked in: the first time you open the shade, it can come out of the bracket.
STEP 6
Fit all the magnetic covers on both plates.
On the motorized version, first check that the antenna is in its recess.

SO, WHAT DO YOU NEED TO DO?
Close the two brackets with the covers.
⚠ WARNING
Don't fit the covers before routing the antenna.
You'd have to take them off again to reach the recess.
STEP 7A
MANUAL SHADES ONLY
If your shade is motorized, go to step 7B.
Attached to the chain you'll find the safety chain tensioner, the wall anchor to fix it and a leaflet. The tensioner keeps the chain taut and stops it from forming a loop, which is dangerous for children. Fixing it to the wall is mandatory: it's required by the safety standards for indoor window coverings (EN 16433 and EN 16434).

1. Fix the tensioner to the wall with the anchor, below the clutch.

2. Leave the chain slightly taut.

3. Keep the chain straight, in line with the clutch: the shade moves more smoothly.
SO, WHAT DO YOU NEED TO DO?
Fix the tensioner with the chain slightly taut and in line with the clutch.
⚠ WARNING
Don't leave the chain hanging loose.
Without a tensioner it can form a loop, with a risk of strangulation for children or pets. Keep cribs, beds and furniture away from the shade. Remember that the chain must end at least 4' 11" (1.5 m) from the floor.
STEP 7B
MOTORIZED SHADES ONLY
This step only applies if you have a motorized shade with a remote control. The remote has 15 channels, one channel for each shade. Channel 0 lets you control all the shades at once.
In this step you'll often see the word jog: a short movement of the motor in one direction and back. You can see it in the fabric, which rises and drops slightly.

Press the P1 button on the motor until the motor jogs and beeps.

Within 10 seconds, press STOP on the remote for 2 seconds. The motor jogs twice and gives 3 short beeps: the remote is paired.

Press UP: the shade should go up.

If the shade goes down instead of up, hold UP and DOWN together for 2 seconds. The motor jogs and gives a short beep: the direction is reversed.
The limits are the points where the shade stops by itself, at the top and at the bottom.

Top: press UP for 2 seconds, stop the shade at the height you want and hold UP and STOP together for 2 seconds. Two jogs and 3 short beeps: upper limit set.

Bottom: press DOWN for 2 seconds, stop the shade where you want and hold DOWN and STOP together for 2 seconds. Two jogs and 3 short beeps: lower limit set.
Hold UP and STOP (for the upper limit) or DOWN and STOP (for the lower limit) for 5 seconds: one jog and one beep. Bring the shade to the new height with UP or DOWN, then hold UP and STOP, or DOWN and STOP, again for 2 seconds. Two jogs and 3 short beeps: new limit saved.
You can only do this after setting both limits.
To recall it, hold STOP for 2 seconds.
Press P2 on the back of the remote until the motor jogs and beeps, then STOP until it jogs and beeps, then STOP again: one jog and a long beep, position deleted.
You need the remote that's already paired (A) and the new one (B).
To remove B, repeat the same sequence: at the end, B no longer controls the shade.
Press P1 on the motor for 2 seconds: one jog and a long beep. Then press STOP on the remote for 2 seconds: two jogs and 3 short beeps, remote unpaired.
To increase it: press P2 (one jog and one beep), then UP (one jog and one beep), then UP again (two jogs and 3 beeps). To decrease it, do the same with DOWN instead of UP. If the motor doesn't respond, it's already at maximum or minimum speed.
Switch to another channel with the CHANNEL UP and CHANNEL DOWN buttons and repeat the pairing. If you can't change channel, hold CHANNEL UP and CHANNEL DOWN together for 3 seconds: a number appears on the display. Choose how many channels you want to use with CHANNEL UP and CHANNEL DOWN and confirm with STOP.
Hold P1 on the motor for 14 seconds: 4 jogs and 4 beeps. The motor loses its limits, favorite positions and paired remotes, so you'll need to start again from pairing.
SO, WHAT DO YOU NEED TO DO?
Pair the remote and set both limits.
⚠ WARNING
Don't use the shade without limits.
Without set limits, the motor may not stop when closing, or the shade may not open or close fully.
IF SOMETHING DOESN'T WORK
For each problem you'll find the possible causes and what to do. If the problem persists after these checks, contact customer service.
Several motors are paired to the same channel. Pair only one shade per channel.
Check the connections and how the roller tube sits in the brackets. If the noise continues, contact customer service.
It has reached the upper or lower limit. If you want it to stop higher or lower, adjust the limit.
There's dust or something in the way in the moving parts: clean them. If the squeaking continues, the fabric may be misaligned: contact customer service.
Check that nothing is caught between the fabric and the roller tube and remove it. If the problem persists, contact customer service.
The limits aren't set correctly. Set them again as in step 7B; if that doesn't help, contact customer service.
The remote battery is dead: replace it.
Pair the remote again as in step 7B, then check the remote battery and the motor battery, and recharge the motor. If it still doesn't move, contact customer service.
CLEANING AND MAINTENANCE
Turn off the motor before cleaning
On the motorized version, switch off the motor with its button before any cleaning or maintenance.
Clean the fabric only with a damp cloth and lukewarm water. Don't wash it in water, don't put it in the dryer, don't wring it, don't iron it and don't use bleach.
Dust the fabric with a vacuum cleaner or with a sponge or damp cloth and lukewarm water, then let it dry. This prevents dust and dirt from causing mold. Clean the aluminum parts with water and a mild detergent.
Check that the shade goes up and down smoothly. If you notice wear, tears or unusual movements, contact customer service.
Only use the power adapter provided: the motor charges via a 5 V USB-C cable. Don't connect it to other power adapters.
ARGOMENTO (INSERIRNE UNO PER OGNI SEZIONE DELLA GUIDA)